Pine Hills Elite Fence: Fence Installation and Repair in Pine Hills, FL
We provide professional residential and commercial fence installation, gate automation, and storm damage repair across Pine Hills, FL, and Orange County. Our crew builds low-maintenance vinyl, wood, aluminum, chain-link, and composite fencing engineered to withstand Central Florida humidity and storm winds.
Affordable Cost Transparency
Full itemized estimates upfront. Installed pricing: $14–$25/lf for chain link, $18–$35/lf for pressure-treated wood, $25–$45/lf for aluminum, and $25–$50/lf for rot-proof vinyl. Single walk gates run $200–$600, double drive gates $500–$2,500, automatic openers $1,500–$5,000+, and old fence removal $3–$9/lf.
Payment Terms & Schedule
Only an initial deposit locks in your project date, with the final balance due after walkthrough approval. Permit reviews and HOA approvals take 2 to 6 weeks, but our on-site build takes just 1 to 3 days.
Fencing Styles & Storm Resistance
Choose from privacy vinyl, powder-coated aluminum, wood, and chain link. Privacy layouts use shadowbox or board-on-board designs to allow wind airflow during severe Florida storms.
Concrete Anchoring & Code Compliance
Terminal posts are set in concrete with a 24-to-72-hour cure time before hanging panels. We complete 811 utility locates before digging and build pool enclosures to meet Orange County self-closing gate codes.
Get a FREE Quote.
Before and After Fence Projects
160 Linear Foot Rot-Proof Tan Vinyl Privacy Fence Installation
Marcus and Alicia were tired of constantly repairing an aging, termite-eaten wood fence that was rotting from Central Florida’s ground moisture and heavy summer rain. They wanted a zero-maintenance privacy boundary for their backyard. Our crew managed Orange County permits and coordinated 811 Sunshine State utility locates before tearing out 160 feet of decaying wood and pulling up old footings. We set heavy-duty vinyl posts 30 inches deep in high-strength concrete, allowing a full 48-hour cure time before hanging 6-foot tan privacy panels equipped with UV inhibitors to prevent yellowing under the Florida sun. We installed a 4-foot pedestrian walk gate and a 10-foot double drive gate with stainless steel drop rods. The result is a clean, maintenance-free perimeter that resists rot, mildew, and termites for decades.
- Scope & Scope Size: 160 linear feet of 6-ft tan vinyl privacy fencing with 1 single walk gate (4-ft) and 1 double drive gate (10-ft)
- Turnaround Time: 2 business days on-site installation (after Orange County permit approval)
- Final Project Cost: $5,600 complete (includes old termite-damaged wood fence tear-down, haul-away, 811 Sunshine State utility locate, concrete post footings, and UV-stabilized vinyl panels).
120 Linear Foot Code-Compliant Powder-Coated Aluminum Pool Enclosure
After installing a new in-ground swimming pool, Derek and Sarah needed an elegant, rust-proof safety barrier to comply with strict Orange County residential pool safety codes and keep their two young children safe. Our crew core-drilled the concrete pool deck and patio perimeter to anchor 2-inch square aluminum posts in non-shrink hydraulic cement. We installed 4-foot flat-top black aluminum panels with picket spacing under 3.75 inches to prevent small children from squeezing through. We equipped both access gates with MagnaLatch self-closing magnetic latches mounted at the required 54-inch code height with out-swinging hinges. The installation passed Orange County pool safety inspection on the first visit, providing complete child safety without blocking pool views from the kitchen window.
- Scope & Scope Size: 120 linear feet of 4-ft black powder-coated aluminum pool fencing with 2 self-closing, self-latching pool gates
- Turnaround Time: 1 business day on-site installation
- Final Project Cost: $3,900 complete ($30/lf installed plus 2 self-closing magnetic latch pool gates and concrete pool deck core-drilling)
180 Linear Foot Storm-Resistant Pressure-Treated Wood Board-on-Board Privacy Fence
Severe tropical storm wind gusts blew down a 50-foot section of Christopher and Elena’s old stockade fence, completely exposing their backyard and patio to Pine Hills Rd. To prevent future storm blowout, we designed a heavy-duty board-on-board privacy fence using overlapping 1x6 pressure-treated pine pickets that allow severe wind pressure to filter through subtle air channels. We set 4x4 line posts and 6x6 gate terminal posts 3 feet deep into solid concrete footings. All rails were secured using hot-dipped galvanized ring-shank nails and stainless steel brackets to prevent rust staining. The completed 6-foot privacy fence delivers 100% visual privacy from the street while engineered to withstand Central Florida’s summer hurricane season.
- Scope & Scope Size: 180 linear feet of 6-ft pressure-treated pine board-on-board privacy fence with 1 wide equipment gate
- Turnaround Time: 2 business days on-site installation
- Final Project Cost: $4,850 complete ($24/lf installed including 6x6 pressure-treated corner posts, hot-dipped galvanized fasteners, tear-down, and site cleanup)
Residential Fence Installation in Pine Hills, FL
Central Florida homeowners choose fences based on climate resistance, upkeep, privacy, and local rules. We install wood, vinyl, aluminum, chain link, wrought iron, composite, and other styles, along with gates and pet enclosures, built for heat, humidity, and summer storms.
Wood Fences
A natural look at a moderate price. We install pressure-treated pine, cedar, and cypress. Cedar and cypress resist rot and insects better than pine. Heights run from 4 to 8 feet, with 6 feet the most popular. Wood needs sealing or staining every 2–3 years in Florida’s humidity.
Vinyl Fences
Vinyl won’t rot, rust, or attract termites, and it only needs an occasional wash. Styles include privacy, semi-privacy, picket, and ranch rail, in white, tan, or gray. UV inhibitors in quality panels resist yellowing. It costs more upfront than wood but skips the staining and repainting.
Aluminum Fences
Rust-resistant and lightweight, with a powder-coated finish that holds its color. It comes in black, bronze, or white.
- Heights: 4 to 6 feet
- Picket spacing: under 4 inches for pool code
- Styles: flat top, spear top, puppy picket
Aluminum is ideal for pools, front yards, and property lines.
Chain Link Fences
One of the most affordable and fastest fences to install. It comes in galvanized or vinyl-coated steel, in black, green, or brown. Typical heights are 4 and 6 feet. It keeps kids and pets in, and privacy slats can add screening. Heavier-gauge wire and well-set terminal posts help it last.
Privacy Fences
Blocks views and reduces some noise. It’s built from wood, vinyl, or composite, usually 6 feet tall, the height most Orange County rear yards allow. Posts are set deep in concrete for storm season. Board-on-board or shadowbox styles let air through to reduce wind stress.
Pool Fences
Built to Florida pool barrier rules:
- Minimum 4-foot height
- Openings too small for a child to pass through
- Self-closing, self-latching gates that open outward
- Latches out of children’s reach
Available in aluminum, vinyl, or removable mesh. We review permit and inspection requirements before we start.
Wrought Iron Fences
Strong and classic, usually made today from ornamental steel. A primed, powder-coated finish protects against humidity. Touch up chips promptly to stop rust. It’s heavy, so posts and footings are set carefully. It’s well suited to front yards and entrances, and costs more than aluminum.
Composite Fences
Wood fibers and recycled plastic give a wood look without rot, insects, or warping. No staining or sealing is needed, just soap and water. We leave gaps for heat expansion in the Florida sun. It costs more upfront than wood but lasts long with little care.
Picket Fences
A traditional look for front yards and garden borders, usually 3 to 4 feet tall. It’s available in wood, vinyl, or aluminum. It marks boundaries and keeps small pets and kids in, but doesn’t give privacy. Pointed, dog-ear, or scalloped tops and decorative post caps let you choose the style.
Ranch and Split Rail Fences
Defines larger lots without blocking views. It has 2 to 4 horizontal rails, with posts set 8 to 10 feet apart. It comes in pressure-treated pine, cedar, or low-maintenance vinyl. Adding welded or woven wire mesh makes it pet-ready. It costs less per foot than privacy fencing.
Driveway Gates and Automatic Gate Openers
Swing or sliding gates for security and vehicle access, chosen to fit your driveway’s slope and clearance. The openers work by remote, keypad, or smartphone app, with:
- Battery backup for power outages
- Safety sensors
- Solar options
Gate posts get strong footings. Permits apply to electrical work.
Dog and Pet Fences
Height matches your dog: 4 feet for small breeds, 5 to 6 feet for larger or athletic dogs. For diggers, we bury mesh or set panels below grade. It’s available in vinyl-coated chain link, narrow-picket aluminum, or wood privacy, with latches dogs can’t open.
Commercial Fence Installation in Pine Hills, FL
Commercial properties in Pine Hills need fencing that meets Orange County code, holds up to Central Florida heat, humidity, and afternoon storms, and fits the way each site operates. We install chain link, aluminum, vinyl, wood, and steel systems for job sites, warehouses, communities, schools, athletic facilities, and public property.
Construction Site and Temporary Fencing
Perimeter control from day one, to keep people out, protect materials, and meet insurance requirements.
- 6-foot temporary panels on stands or concrete bases
- 8-foot chain link for higher-risk sites
- Privacy windscreen with branding
- Double-drive gates for trucks and equipment
We plan fence lines around utilities, sidewalks, and drainage.
Industrial and Warehouse Fencing
Controls access and deters theft without slowing deliveries. We install galvanized chain link at 8 feet or taller, with barbed wire where code allows. Heavy-duty posts, tension wire, and bottom rails hold it tight against wind and traffic. Gate options include rolling cantilever, swing, and pedestrian gates, plus keypad or card reader integration.
Apartment and HOA Community Fencing
Separates communities from roads, retention ponds, and neighboring parcels. Aluminum picket is the most common choice. We use vinyl privacy fencing for dumpsters and utilities, and wood or composite where a board prefers. Pool enclosures meet Florida barrier rules. Send us your HOA guidelines so materials and colors match.
Retail and Commercial Property Fencing
Defines outdoor space, screens service areas, and directs foot traffic. We install ornamental aluminum for patios and storefronts, and vinyl or wood privacy panels for back-of-house areas. Gated patios help with alcohol service rules. Solid fences reduce noise and light spillover onto homes next door. Finishes come in black, bronze, white, or tan.
School and Daycare Fencing
Keeps children in and unauthorized people out. We use 4- to 6-foot aluminum or vinyl-coated chain link, with no climbable footholds or sharp edges. Self-closing hinges and latches are set out of children’s reach. We build to Florida childcare licensing requirements for outdoor play areas.
Sports Field and Tennis Court Fencing
Stands up to ball impact while keeping sightlines clear. Tennis and pickleball courts get 10- to 12-foot vinyl-coated chain link in black or green. Baseball and softball fields get backstops, dugout fencing, and outfield lines.
- Windscreens
- Court gates for maintenance equipment
- Ball-stop netting
Dumpster and Equipment Enclosures
Keeps waste areas tidy and meets screening rules. We build with vinyl, wood, or aluminum panels and wide, heavy-duty gates for service trucks. Steel gate frames and reinforced hinges prevent sagging. We also enclose HVAC units, generators, transformers, and pool equipment, using louvered or slatted designs that allow airflow and technician access.
Self-Storage and Parking Lot Fencing
We install 8-foot chain-link or ornamental steel, with keypad or electric sliding entrance gates. Parking lot fencing can:
- Direct traffic to entrances and exits
- Secure fleet parking after hours
- Separate the lot from neighboring property
- Protect landscaping and retention areas
Fleet yards can add privacy slats. Posts and gates are placed clear of cameras and lighting.
Municipal, Park, and Security Fencing
Durable, low-maintenance chain link, ornamental steel, and aluminum for parks, retention ponds, utility sites, and municipal facilities. Higher-security options include anti-climb mesh, taller heights, and reinforced posts. For bid-based public work, we provide itemized estimates so you can compare proposals and confirm the fence meets your project specifications.
Specialty Fence Services in Pine Hills, FL
Beyond new installations, we handle repairs, replacements, gate work, storm damage, finishing, and custom builds for Pine Hills properties. Each service addresses a specific problem common to Central Florida fences, from humidity and heavy rain to hurricane-season wind.
Fence Repair and Maintenance
Most fence problems start small. A loose picket, a cracked rail, or a sagging section of chain link is inexpensive to fix when caught early, and costly to ignore through a summer of storms.
We repair wood, vinyl, aluminum, and chain link fences, matching the existing material as closely as possible. Common repairs include:
- Replacing broken pickets, rails, and vinyl panels
- Re-securing loose fasteners and brackets
- Patching chain link tears and re-tensioning fabric
- Replacing rusted or damaged hardware
Routine maintenance extends the life of a fence. We recommend a walk-through inspection twice a year, ideally before the June start of hurricane season and again after it ends. Look for soft wood, rust streaks, shifting posts, and gaps under the fence line.
If a repair would cost more than half the price of replacement, we will tell you so you can compare both options.
Fence Replacement and Old Fence Removal
Some fences are past the point of repair. Signs include widespread rot, posts that no longer hold firm in the ground, or panels that fail repeatedly after patching.
We handle the full process, starting with tear-down and haul-away of the old fence. This includes pulling posts and removing concrete footings so the new fence can be set in solid ground.
Material | Typical Lifespan in Florida |
|---|---|
Pressure-treated wood | 10–15 years |
Vinyl | 20–30 years |
Aluminum | 25+ years |
High-traffic hallways | 15–20 years |
Lifespan varies with installation quality, soil conditions, and maintenance. Replacing a fence also gives you a chance to change materials, height, or style. Many Pine Hills homeowners move from wood to vinyl or aluminum to reduce upkeep in the humid climate.
Gate Repair and Automatic Gate Openers
Gates carry more stress than any other part of a fence because they move every day. Sagging, dragging, and latches that no longer line up are the most common complaints.
We repair and adjust:
- Sagging or dragging gates, often fixed with new hinges, a gate wheel, or an anti-sag kit
- Latches and locks that no longer catch
- Cracked frames and damaged gate panels
- Bent or rusted hardware
We also install automatic gate openers for driveway and entry gates. Swing gates and slide gates use different operators, so the right choice depends on your driveway slope, available space, and gate weight.
Typical features include remote controls, keypads, battery backup, and safety sensors that stop the gate if something is in its path. We can also add backup power so the gate works during outages, which are common after storms.
Fence Post Repair and Leaning Fence Correction
Posts are the foundation of any fence. When a post shifts, the rails and panels attached to it shift too, and the problem tends to spread along the fence line.
Leaning is usually caused by one of the following:
- Rotted wood at or below ground level
- Posts set too shallow or without enough concrete
- Saturated soil after heavy rain
- Wind load on solid privacy panels
We assess each leaning section before choosing a fix. If the post is sound, we can reset it in new concrete. If it has rotted, we replace it and reattach the panels.
Where possible, we use galvanized post anchors or concrete footings sized to the fence height so the repair holds. Fixing one post early is far cheaper than rebuilding a full run later.
Fence Staining, Painting, and Sealing
Sun, rain, and humidity break down unprotected wood quickly in Central Florida. Fading, graying, mildew, and cracking are all signs that the finish has failed.
We apply stains, paints, and sealers suited to the fence material. For wood, the common choices are:
Finish | Appearance | Typical Reapplication |
|---|---|---|
Clear sealer | Natural wood tone | Every 1–2 years |
Semi-transparent stain | Color with visible grain | Every 2–3 years |
Solid stain or paint | Full color coverage | Every 3–5 years |
Preparation matters as much as the product. Wood should be clean and dry before application, and new pressure-treated lumber often needs several weeks to dry out first. We also treat metal fences, scraping rust and applying a rust-inhibiting primer and paint to aluminum and steel.
Fence Cleaning and Pressure Washing
Algae, mildew, dirt, and pollen build up on fences in Pine Hills year-round. Green or black film on vinyl and wood is usually organic growth, and it can trap moisture against the surface.
We pressure-wash fences at settings matched to the material. Wood needs lower pressure to avoid gouging the grain, while vinyl and aluminum tolerate more. We use cleaning solutions to kill mildew at the source, not just rinse the surface.
Cleaning is also the first step before staining or sealing, since finishes will not bond well to a dirty surface. For vinyl and aluminum fences, an annual wash is often enough to keep them looking new.
Why Pine Hills Elite Fence Is Orange County's Trusted Fencing Contractor
We build and repair fences for homeowners and businesses throughout Pine Hills and the surrounding Orange County communities. Our work centers on clear communication, sound materials, and installations that hold up to Central Florida's heat, humidity, and storm season.
What you can expect when you work with us:
- Written estimates that list materials, labor, and timelines
- Fences built to local permit and setback requirements
- Straightforward answers about cost, lifespan, and maintenance
- Cleanup of the job site once the work is complete
We install the fence types that suit most properties in the area, including vinyl, aluminum, wood privacy, chain-link, and ornamental iron. Each material performs differently in Florida's climate, so we explain the trade-offs before you choose.
Fence Type | Best For | Florida Consideration |
|---|---|---|
Vinyl | Privacy, low upkeep | Resists rot and termites |
Aluminum | Pool areas, curb appeal | Does not rust |
Wood | Natural look, privacy | Needs regular sealing |
Chain-link | Budget, large areas | Durable and easy to repair |
We also handle gates, post replacement, and storm damage repair. Many pool enclosures in Orange County must meet safety codes, and we build compliant gates and latches for those properties.
You can ask us about licensing, insurance, and past projects at any point before you sign. We would rather you make an informed decision than rush into one.
Fence Installation Timeline in Pine Hills, FL
Most residential fence projects in Pine Hills take about 2 to 6 weeks from the first estimate to completion. The on-site build usually takes only 1 to 3 days. Most of the time goes to permits, utility locates, and ordering materials.
How Long Does Fence Installation Take?
Typical timelines for a residential fence:
Stage | Typical Time |
|---|---|
Estimate and measurement | 1 visit, written estimate within a few days |
Permit review (Orange County) | Several days to 2+ weeks |
811 utility locate | 2 full business days before digging (Florida law) |
Material ordering | 1–2 weeks for stock items, 3–6 weeks for custom gates or special colors |
Post setting and concrete cure | 1 day, with 24–72 hours of cure time before load-bearing work |
Panel installation and gate hanging | 1–2 days for most yards |
Final walkthrough and inspection | Same day as completion, with any county inspection scheduled where required |
The schedule can be affected by fence length, material availability, permit review backlogs, HOA approval, slopes, rock or roots, and rain. Summer storms often push back digging and concrete work.
Project Timeline & Milestones
- Consultation: We discuss your goals, budget, and fence options.
- Site measurement and survey review: We measure the fence line and check it against your property survey.
- Material selection: You choose the material, height, style, color, and gates, and approve the written estimate.
- Permit submittal: We help prepare the Orange County permit application and any HOA approval request.
- Scheduling: Once the permit and materials are ready, we book your installation date and request the 811 locate.
- Post setting: Posts are set in concrete and left to cure.
- Installation: Panels, rails, or fabric go up, and gates are hung and adjusted.
- Cleanup: We remove debris, extra soil, and packaging from the site.
- Final walkthrough: We walk the fence line with you, test the gates and latches, and confirm the work matches the agreement.
Inspection / Measurement / Assessment
Before installation, we check the site for anything that affects layout, cost, or timing:
- Property lines: We review your survey so the fence sits within your boundary.
- Linear footage: We measure every run, corner, and gate opening.
- Grade and slope: We check where panels need to be stepped or racked.
- Soil and drainage: We check for sandy soil, hardpan, low spots, and water flow, so the fence doesn't block drainage.
- Existing fencing: We check whether the old fence and its footings need to come out.
- Trees and roots: We check for roots and nearby trees that may shift post locations.
- Utilities: We note marked lines and easements along the fence path.
- Gate placement: We confirm the gate width and that each gate has room to swing or slide.
Design / Planning Process
With the measurements in hand, we plan the layout and confirm the details with you:
- Layout: The fence line, corners, and transitions around the house and landscaping.
- Style and height: Privacy, picket, ornamental, or ranch rail, at heights allowed for front, side, and rear yards.
- Material and color: Wood, vinyl, aluminum, chain link, or composite, in colors that fit your home and HOA rules.
- Gates: How many, how wide, and where, including drive gates for vehicles or equipment.
- Post spacing: Spacing set to the material and wind exposure, typically 6 to 8 feet.
- Hardware and automation: Latches, hinges, locks, pool-code hardware, and optional gate openers.
- HOA and code review: We check the design against Orange County rules and your association's guidelines.
- Drawings and approvals: A site sketch for the permit and HOA submittal, with final sign-off before ordering materials.
Fence Installation Cost & Pricing in Pine Hills, FL
Fence pricing depends on your property, the material, and the site work involved. The ranges below are typical for the Orlando area and are meant for planning only. Your written estimate lists the exact figures for your project.
What Affects Cost?
The main factors are linear footage, material, fence height, and labor. Post spacing and depth, the number and type of gates, and gate automation also add cost. So do slopes, tree roots, old fence removal, and permits. Fences over 6 feet in Orange County need a building permit as well as a zoning permit. Commercial jobs may also call for heavier materials, taller heights, or access control.
How Much Does a New Fence Cost?
Most residential fences are priced per linear foot, installed. Typical Orlando-area ranges for 4- to 6-foot fences:
Material | Typical Installed Cost per Linear Foot |
|---|---|
Chain link (galvanized) | $14 – $25 |
Wood (pressure-treated pine) | $18 – $35 |
Aluminum | $25 – $45 |
Vinyl | $25 – $50 |
Composite and ornamental steel | Quoted per project |
Gates, removal, and permits are priced separately:
Item | Typical Cost |
|---|---|
Walk gate | $200 – $600 each |
Double drive gate | $500 – $2,500 each |
Automatic driveway gate system | $1,500 – $5,000+ |
Old fence removal | $3 – $9 per linear foot |
Orange County residential fence permit | From $38, plus county fee schedule |
Repairs, staining, and commercial fencing are quoted per job, based on materials, access, and scope.
Budget Planning
Divide your budget into materials, posts and footings, gates and hardware, automation, removal and disposal, permits, finishing, and labor. As an example, 150 feet of 6-foot wood privacy fence at $18–$35 per foot comes to about $2,700–$5,250 before gates and removal. Posts, footings, and gate hardware carry the most stress, so they are worth spending on.
Professional Fence Installation vs DIY
DIY saves on labor, but it leaves you responsible for the property line, the permit, the 811 utility locate, and setting posts at the right depth. You also have to rent the equipment and set aside several weekends. Professional installation includes the tools, faster completion, and a written workmanship warranty. For long runs, slopes, gates, and pool barriers, it reduces the risk of costly rework.
Hidden Costs & Additional Considerations
Watch for old fence removal and disposal, land clearing, tree roots and stumps, grading on slopes, and rock or hardpan below the surface. Survey fees, HOA material requirements, and specialty hardware such as pool-code latches can also add cost. If something unexpected comes up during installation, we explain it and agree on any change in writing before continuing.
Financing / Payment Structure
Payments follow clear steps. After the estimate, a deposit reserves your installation date and covers ordering materials. The remaining balance is due after a final walk-through once the work is complete. Every payment term is listed in your written agreement before work begins.
Frequently Asked Questions
We install fences for residential and commercial properties throughout Pine Hills and nearby Orange County communities. Our most common projects use aluminum, vinyl, wood, and chain link.
Aluminum works well for pool enclosures and decorative front yards. Vinyl and wood suit privacy fences, and chain link is a practical choice for large lots, commercial sites, and pet enclosures.
We also build gates, including walk gates and driveway gates, to match the fence style you choose. If you are unsure which material fits your property, we can walk you through the options during your estimate.
Cost depends on the material, the fence height, the total linear footage, and the number of gates. Site conditions such as slopes, tree roots, and old fence removal also affect the price.
As a general range, chain link costs the least per linear foot. Wood and vinyl fall in the middle, and aluminum typically costs more than both because of the material and its longer lifespan.
We provide a written estimate after we review your property, so you see the exact figures for your project before any work begins.
We install aluminum fencing, and the brand of panels used depends on the project, the grade you need, and current availability. Elite Fence Products is a separate American manufacturer of aluminum fence systems, and its name is similar to ours, so the two are easy to confuse.
If you want a specific manufacturer or grade, tell us when you request your estimate. We can confirm which products we can supply for your property.
Residential and commercial aluminum grades differ in picket thickness and post strength, so we match the grade to how the fence will be used.
In most cases, yes. Pine Hills is an unincorporated community in Orange County, so fence permits and zoning rules generally come through the county rather than a city office.
Requirements can vary by fence height, location on the lot, and whether the fence is near a pool or a corner where sight lines matter. Many neighborhoods also have homeowners association rules that limit materials, heights, or colors.
We recommend that you check with Orange County and your HOA before you sign a contract. We can help you understand what your project is likely to need, but you remain responsible for confirming the final requirements for your address.
Warranty coverage has two parts. Manufacturers warrant their materials, such as aluminum panels, vinyl, and hardware, and the terms differ by product and brand.
We stand behind our installation workmanship, and we put the warranty terms for your specific fence in writing before work starts. Coverage periods and exclusions depend on the material you select.
Normal wear, storm damage, and damage caused by impact are generally not covered. Ask us to review the warranty with you so you know what applies to your fence.
You can contact us by phone or through the contact form on this website. Please tell us your address, the type of fence you want, the approximate length, and whether you need gates.
We schedule a visit to measure your property and look at the layout, soil, and any obstacles. After the visit, we send a written estimate that lists materials, labor, and a projected timeline.
Photos of your yard and any HOA guidelines you have are helpful to include with your request.